Post Falls Electrical Company handles the full range of electrical work for homes, rental properties, apartment buildings, and commercial spaces across Post Falls and Kootenai County. Whether you are a homeowner dealing with a tripping breaker, a landlord coordinating repairs between tenants, a property manager keeping a building up to code, or a business owner planning a remodel, we scope the job on the call and get it scheduled. We are open 7 days a week, 7:30 AM to 11:00 PM. Safe wiring. Solid workmanship. Straight answers.
Call (986) 946-5326 for a quote.
Seeing flickering lights or a warm outlet? Those are the kinds of calls worth taking seriously. A flickering light can point to a loose connection, a failing breaker, or a wiring problem deeper in the circuit. A warm or discolored outlet, a burning smell near the breaker box, or a breaker that trips repeatedly and will not stay reset are all signs that something needs to be traced before it becomes a bigger problem.
We handle partial power loss, too. When half the house goes dark or a section of outlets stops working, the cause is not always obvious. It could be a tripped double-pole breaker, a failed GFCI upstream from a string of outlets, or a wiring fault in the circuit. We run the fault down before anything is replaced, so you know exactly what failed and why.
GFCI and AFCI protection are part of this work as well. Arc-fault and ground-fault breakers are required in most areas of a modern home, and an older house that has never had them installed carries real risk. If your breaker box has neither, that is worth knowing. Reach out and we'll get it diagnosed.
We install and replace outlets of every type: standard duplex outlets, GFCI outlets for kitchens, bathrooms, and garage spaces, AFCI outlets, and USB combination outlets where you want a charging point without an adapter block. Switch work runs from a basic single-pole replacement to dimmer installation and three-way switch wiring.
Lighting covers a wide range. Recessed LED lighting, light fixture installation and replacement, under-cabinet lighting, and exterior security lights are all common requests. For outdoor work, we wire motion sensor lights, landscape lighting, and security lighting for driveways and entryways. Bathroom exhaust fan wiring falls here too, whether it is a straight replacement or a new run.
Ceiling fan installation is one of the more involved lighting jobs when there is no existing wiring or box in the ceiling. We handle the full run, from the panel to the switch to the fan, including proper box support for the fan's weight. When the job is done, we leave your home clean and powered, the work area left as it was found. Call and we'll handle the lights, outlets, and panel.
Older homes in Post Falls and across Kootenai County often came with 100-amp service, and that capacity does not stretch far in a modern household. We handle the full panel conversation: upgrading from 100-amp to 200-amp service, replacing a main panel, converting a fuse box to a modern breaker panel, and installing subpanels for detached garages, shops, or home additions.
Service-entrance and meter upgrades go hand in hand with panel work when the utility connection itself needs to grow with the load. We run load calculations to confirm what the service needs to carry before any work is scoped, so the upgrade is sized correctly the first time.
Code compliance comes up here regularly. A failed electrical inspection or a panel flagged during a home sale can hold up a closing or a permit. We handle code violation repair and bring panels and wiring up to current standards. An older panel is worth a look before a big appliance goes in. Pick up the phone and we'll get rolling.
If your home has knob-and-tube wiring or aluminum branch-circuit wiring, replacement or remediation is not a small job, but it is a straightforward one when it is scoped clearly. We handle whole-home rewiring for older houses, knob-and-tube replacement, and aluminum wiring repair and replacement. Grounding and bonding are part of that work, and we confirm both are correct before the job closes.
Dedicated circuits are one of the most common requests we handle. A refrigerator, dryer, washer, dishwasher, microwave, and range each benefit from a circuit that is not shared with other loads. When a central air conditioner or heat pump is being installed, we handle the electrical side: running the dedicated circuit, installing the disconnect, and confirming the panel has the capacity to carry the load. We do not install or service the cooling equipment itself, but the power side is our work.
We also install 240-volt outlets for dryers and ranges, run circuits for home additions and remodels, and handle new construction wiring from rough-in to finish. Rental property wiring and commercial spaces, including office and retail buildouts, are part of our regular work. We treat your home and its wiring the way we would our own, and that carries over to every property type. One call and we are on it.
Kootenai County winters are hard on electrical systems in ways that warmer climates never see. Extended sub-freezing temperatures, ice storms, and wind events can knock out power for multiple days. Electric heating loads push older panels close to their limits. Frozen pipes and roof ice dams are routine seasonal problems. The three services below come up constantly in this area for those reasons.
When a storm takes out power in Post Falls, it is not always restored quickly. Rural-edge properties and areas near the county line can sit without power for an extended stretch. A backup generator with a properly installed transfer switch means the circuits you need most stay live: the well pump, the refrigerator, the heating system's electrical supply.
We handle the full hookup: transfer switch installation, panel connection, load assessment, and grounding and bonding for the generator. The transfer switch is what keeps the generator from back-feeding the utility line, and it has to be wired correctly. We scope the load before the job starts so the generator is matched to what you actually need to run.
Post Falls has grown fast, and a lot of that growth means older homes are being asked to carry loads they were never designed for. A new EV charger, a home addition, a detached shop, or a second HVAC unit can push a 100-amp panel past what it can handle safely.
We upgrade panels from 100-amp to 200-amp service, replace fuse boxes with modern breaker panels, and install subpanels for additions and outbuildings. Load calculations are part of every panel job so the new service is sized for what is actually on the circuits, not just what was there when the house was built. All work is done to the code inspectors in Kootenai County enforce.
Freeze cycles in Post Falls hit exposed pipes, roof edges, and gutters hard. Heat tape is a practical solution, but it has to be wired correctly to be safe. A heat tape circuit that is overloaded or unprotected is a fire risk, and a lot of older installations were done without the GFCI protection the circuit requires.
We install dedicated circuits for heat tape systems, wire the circuit with proper GFCI protection, and confirm the load is within what the circuit is rated to carry. If you are adding heat tape to a roof edge or a pipe run for the first time, we handle the circuit from the panel out. If an existing circuit needs to be brought up to current standards, we can assess and correct it.
If you're not sure your panel can handle the load, an EV charger installation starts with that question. A Level 2 charger runs on a dedicated 240-volt circuit, and the panel needs to have the capacity before anything is connected. We check the panel first, handle any needed upgrade, run the dedicated circuit, and install the charger outlet. The rate and what it covers are confirmed on the call before anything is scheduled.
Whole-home surge protection is worth considering in any area that sees ice storms and power fluctuations. A surge protector installed at the panel catches voltage spikes before they reach appliances, electronics, and HVAC equipment. It is a single installation that covers the whole house rather than relying on individual power strips at each outlet.
Electrical safety inspections are available for pre-purchase home buyers, landlords preparing a rental unit, and property owners following a renovation. We go through the panel, the wiring, the outlets, and the grounding to give you a plain answer on repair versus upgrade where anything needs attention. Pick up the phone and we'll get rolling.
We work for homeowners, landlords, property managers, apartment owners, and commercial clients across Post Falls and the surrounding area. For residential customers, that means everything from a single outlet repair to a full rewiring project. For rental property owners, we coordinate access and scheduling to minimize disruption between tenants. For property managers handling multiple units, we handle scope and pricing on the call so there are no back-and-forth delays.
Commercial work includes office spaces, retail buildouts, light industrial, and new construction. If you are managing a remodel or a tenant improvement, we can work within your project schedule. Not the biggest name in town. Just the one that answers. No runaround. We are available 7 days a week, 7:30 AM to 11:00 PM, including evenings and weekends. Call and we'll handle the lights, outlets, and panel.
We know schedules shift, so we keep booking flexible, and we take short-notice calls when the schedule allows. Emergency electrical repair is available. When you call, we scope the job on the phone, confirm the rate, and get you on the calendar. The price is confirmed before anything is scheduled, and you know what it covers before we show up.
We are open every day from 7:30 AM to 11:00 PM. Plain answers. Clear options. Safe wiring. One call and we are on it.
Post Falls is our primary service area, and we work throughout Kootenai County and the surrounding communities. If you are nearby, give us a call and we will confirm coverage when you reach us.
Nearby areas we serve include:
Call (986) 946-5326 for a quote and we will confirm we can reach you.
We install the transfer switch, run the dedicated circuit from the panel, and confirm the panel has the capacity to carry the added load. The transfer switch is what keeps the generator from back-feeding the utility line, and it has to be sized to the circuits it will protect. We handle the electrical connection. The generator itself is the customer's equipment.
We run a load calculation before any new circuit is added to confirm what the existing panel can carry. If the panel is already near capacity, a service upgrade gets scoped at the same time. An older panel is worth a look before a big appliance or winter load circuit goes in.
Heat tape requires a dedicated circuit sized to the tape's load, GFCI protection at the circuit, and outdoor-rated wiring throughout. The GFCI has to be placed where it can be accessed and tested. We handle the circuit from the panel out, whether it is a new installation or bringing an existing circuit up to current standards.
GFCI protection is required in kitchens, bathrooms, garages, and outdoor locations. AFCI protection is required in bedrooms and living areas in most modern code applications. Older homes in Kootenai County often lack both, and we note where they are missing and required during inspections or repair visits.
A Level 2 EV charger runs on a dedicated 240-volt circuit. We start with a panel capacity check to confirm the existing service can carry the added load. If the panel has room, we run the circuit and install the outlet or hardwired connection. If the panel is near capacity, a service upgrade is scoped at the same time.
A surge protector installed at the main panel catches voltage spikes before they reach the branch circuits and the appliances connected to them. It handles large events from lightning or grid fluctuations that a power strip suppressor cannot absorb. It does not replace point-of-use protection for sensitive electronics, but it covers the whole house at the point of entry.
A full rewire is typically needed when a home has knob-and-tube wiring throughout, when wiring damage is widespread, or when a major renovation exposes the existing wiring and it cannot safely remain. Partial rewiring targets specific runs or rooms where the existing wiring is no longer up to the job. We assess what is there and explain the options before any work is scoped.
Aluminum branch-circuit wiring is addressed by installing properly rated devices and connections at every termination point. This handles the oxidation and heat issues that make aluminum wiring a concern without requiring a full rewire in every case. We confirm the scope on the call and explain what the remediation covers before scheduling.
Homes built for 100-amp service were designed for a much lighter electrical load than a modern household draws. Adding appliances, home offices, EV chargers, or heating equipment pushes older panels past what they were sized to carry. A load calculation tells us exactly what the panel can support and what needs to change.
We check the breaker condition, load balance across the circuits, grounding and bonding, and whether the service amperage is adequate for the current load. GFCI and AFCI coverage are noted where they are missing and required. If the panel shows signs of wear, overheating, or improper modification, that gets explained before any recommendation is made.
Someone needs to be present to provide access and to go over the scope and the findings before work begins. For rental properties, a tenant can provide access, but we confirm the billing and authorization arrangements with the property owner or manager before the visit.
Post Falls Electrical Company is available 7 days a week, 7:30 AM to 11:00 PM. Whether you need a fast repair, a panel upgrade, a generator hookup, or a full rewiring project, we scope it on the call and get it on the schedule. Safe wiring. Solid workmanship. Straight answers.
Call (986) 946-5326 for a quote.
Below is a plain-language look at the electrical services we handle for homes, rentals, and commercial spaces in Post Falls and across Kootenai County. Each row covers what the service includes, who it fits best, and one practical thing worth knowing before you call. If you have questions about a specific job, we scope it on the phone and confirm the rate before anything is scheduled.
| Type of Work | What It Covers | When You Need It | Things to Know |
|---|---|---|---|
| Outlet & Switch Installation |
| Homeowners updating older outlets or adding charging points without adding adapter clutter | GFCI protection is required in kitchens, bathrooms, garages, and outdoor locations. Older homes in Kootenai County often lack it entirely. |
| Electrical Safety Inspections |
| Home buyers, landlords preparing a rental, or owners following a renovation | An inspection gives you a plain answer on repair versus upgrade for anything that needs attention, before a sale closes or a tenant moves in. |
| Wiring & Rewiring |
| Owners of older homes with original wiring, or anyone planning a major renovation | Aluminum branch-circuit wiring is addressed by installing properly rated connections at every termination point. In many cases a full rewire is not required. |
| Electrical Repairs & Troubleshooting |
| Any homeowner or property manager dealing with an unexplained electrical symptom | The fault is traced before anything is replaced, so you know exactly what failed and why before any work is authorized. |
| Lighting Installation |
| Homeowners remodeling, adding outdoor security lighting, or replacing outdated fixtures | Exterior lighting circuits in Post Falls need to be rated for temperature swings. We confirm the wiring and the fixture ratings match the environment before the job closes. |
| Dedicated Appliance Circuits |
| Homeowners adding a major appliance or converting a space to a workshop or home office | A shared circuit that serves multiple heavy appliances is one of the most common causes of nuisance tripping. A dedicated circuit eliminates the competition for capacity. |
| Whole-Home Surge Protection |
| Homeowners in areas that see ice storms, power fluctuations, or frequent lightning | A panel-level surge protector handles large voltage events that a power strip cannot absorb. It covers every circuit in the house from a single installation point. |
| Ceiling Fan Installation |
| Homeowners adding a fan where no existing wiring or box is in the ceiling | A ceiling fan requires a rated box that can support the fan's weight and motion. A standard light fixture box is not adequate and is a common source of failures. |
| Electrical Panel & Service Upgrades |
| Homeowners adding an EV charger, a detached shop, a home addition, or a second major appliance | An older panel is worth a look before a big appliance goes in. A load calculation confirms what the existing service can carry so the upgrade is sized correctly the first time. |
| Heat Tape Installation |
| Post Falls homeowners dealing with frozen pipes, ice dams, or roof edge buildup during freeze cycles | A heat tape circuit without GFCI protection is a fire risk. Many older installations were done without it. We confirm protection is in place before the job closes. |
| Backup Generator Installation |
| Post Falls homeowners on rural-edge properties or anyone who has lost power for more than a day during a winter storm | The transfer switch is what prevents the generator from back-feeding the utility line. It has to be sized to the circuits it will protect and wired to current code. |
| Breaker & Fuse Repair |
| Homeowners with an older panel or a breaker that keeps failing under normal load | A breaker that trips repeatedly under normal load often points to a wiring issue or an overloaded circuit, not just a bad breaker. We check both before recommending a fix. |
What causes breakers to trip repeatedly?
Repeated tripping usually means one of three things: the circuit is carrying more load than it was sized for, a wiring fault is causing a short or ground fault, or the breaker itself is failing. We run the fault down before recommending a fix, because replacing a breaker on an overloaded or faulted circuit just puts a new breaker in the same problem. The cause gets identified first.
Is the electrical work permitted and inspected?
Work that requires a permit under local code is pulled and inspected. What triggers a permit depends on the scope and the jurisdiction. Panel upgrades, service changes, and new circuit work typically require one in Kootenai County. We confirm what applies to your job before scheduling and handle the process from there.
How do I know if the wiring in my older home is safe?
An electrical safety inspection covers the panel, the wiring, the outlets, and the grounding to give you a clear picture of what is there and what needs attention. Homes in Post Falls built before the 1980s may have knob-and-tube wiring, ungrounded outlets, or aluminum branch-circuit wiring. Each of those carries specific risks, and the inspection tells you what you are dealing with and what the options are.
Faults Traced Before Anything Is Replaced
We identify the cause before recommending a fix. That means you get a plain answer on what failed and why, not a parts swap that leaves the underlying problem in place.
What are the signs a home needs a panel or service upgrade?
Common signs include breakers that trip under normal load, a fuse box that has never been converted to a breaker panel, lights that dim when a large appliance starts, a panel that feels warm to the touch, or a panel that simply has no open slots for new circuits. If you are adding an EV charger, a generator, a detached shop, or a major appliance, a load calculation before the addition is the right starting point.
How are estimates and pricing handled?
We scope the job on the call and confirm the rate before anything is scheduled. You know what the work covers and what it costs before we show up. If the scope changes once the work is underway, we explain what changed and confirm the adjustment before proceeding.
When should I call an electrician rather than attempt a repair myself?
Any work that involves the breaker panel, the service entrance, new circuit wiring, or replacing a breaker is work that should be handled by an electrician. Outlet and switch replacements on a de-energized circuit are within reach for a careful homeowner, but anything involving the panel, grounding, or wiring behind the wall carries real risk if the steps are out of order. A warm outlet, a burning smell, or a breaker that will not stay reset are also calls to make rather than problems to investigate on your own.
Code-Compliant Work on Every Job
Every job is done to the standards the code inspectors in Kootenai County enforce. Where a permit is required, we handle it as part of the work.
How are emergency electrical calls handled?
We take short-notice calls when the schedule allows, and we are available every day from 7:30 AM to 11:00 PM. When you call, we scope what is happening on the phone and confirm whether we can get to you that day. A warm outlet, a burning smell, or a panel that is making noise are situations we treat as urgent.
What do flickering or dimming lights usually mean?
Flickering that affects a single fixture usually points to a loose connection at the fixture, the switch, or the outlet feeding it. Flickering that affects a whole room or a section of the house is more often a loose connection at the panel, a failing breaker, or a wiring fault in the circuit. Dimming when a large appliance starts up can mean the circuit is shared with too heavy a load, or that the panel is near its capacity. We trace the symptom to the source before anything is replaced.
Scope Agreed Before the Panel Is Opened
We confirm the scope and the rate on the call before anything is scheduled. You know what the job covers and what it costs before work begins.
What is the risk of a warm or buzzing outlet?
A warm outlet can mean a loose connection generating heat, a circuit that is overloaded, or a failing device. A buzzing sound from an outlet or a switch often indicates arcing, which is a fire risk. Neither is a symptom to leave unaddressed. Reach out and we will get it diagnosed before it becomes a larger problem.
How long does a panel upgrade or full rewire typically take?
A panel upgrade is usually completed in a single day, including the permit inspection in most cases. A full rewire depends on the size of the home and the condition of the existing wiring, but a typical single-family home runs two to four days. We give you a realistic timeline on the call once the scope is clear, and we confirm any changes before extending the schedule.
Is a home ready for added electrical load after a panel upgrade?
A panel upgrade sized correctly to the load calculation gives you the capacity for what you are adding now and reasonable room for future additions. We confirm the service entrance and the meter are adequate for the new panel size before the upgrade is scoped. If the utility connection needs to grow with the panel, that work is coordinated at the same time.
Call (986) 946-5326 and we will scope the job on the phone, confirm the rate, and get you on the schedule.
(986) 946-5326